Dry-type transformer price: What are the main components and related parts of dry-type transformers?
Release time:
2022-08-10
Dry-type transformer price: What are the main components and related parts of dry-type transformers? Dry-type transformer is not only an important power equipment, but also an important user. Dry-type transformer is an important electrical appliance and a good helper in our production and life. Then the price of dry-type transformer: What are the main components and related components of dry-type transformer?
Dry-type transformer price: What are the main components and related parts of dry-type transformers?
Dry-type transformer is not only an important power equipment, but also an important user. Dry-type transformer is an important electrical appliance and a good helper in our production and life. Then the price of dry-type transformer: What are the main components and related components of dry-type transformer?
Dry-type transformer price: What are the main components and related parts of dry-type transformers?
1. Iron core material The iron core is the main body of the magnetic circuit of the dry-type transformer. The iron core is divided into the core column and the iron yoke, which is sleeved with windings. The yoke is used to close the magnetic circuit. In order to reduce the hysteresis loss and eddy current loss in the iron core and improve the magnetic permeability of the iron core, the iron core is made of silicon steel with a silicon content of about 5%, the thickness is 0.35mm or 0.5mm, and both sides are coated with insulating paint or oxidized.
2. Nuclear structure The core is divided into nuclear structure and shell structure. Iron core dry-type transformer: The 1. secondary winding group of iron core dry-type transformer is set on the two core columns of the iron core, as shown in the following figure. The structure is simple, and all power dry-type transformers adopt heart-shaped structure. Shell-type dry-type transformer: the core of the shell-type dry-type transformer surrounds the upper, lower and side of the winding. Manufacturing complex, more use of small dry-type transformers.
3. Winding (coil) The winding is the circuit part of the dry-type transformer and is made of insulated copper wire or aluminum wire. The winding is the carrier of current, generating magnetic flux and induced electromotive force. High voltage winding: winding with high working voltage; low voltage winding: winding with low working voltage. There are concentric windings and overlapping windings. Concentric winding: The high and low voltage windings are arranged in the same iron core on the same core column, with the low voltage winding inside and the high voltage winding outside, which is convenient to be insulated from the iron core and has a simple structure. Winding: The high and low voltage winding is divided into several pie-shaped coils, which are arranged on the core column along the height of the core column. Concentric winding 1-high voltage winding 2-low voltage winding 3. Accessories of dry-type power transformer include oil tank, oil conservator, tap changer, safety air duct, insulating sleeve, etc. Its role is to ensure the safe and reliable operation of dry-type transformers.
4. Fuel tank: 1-fuel tank; 2-oil storage tank; 3-gas relay; 4-safety air duct is the shell of oil-immersed dry-type transformer for heat dissipation. The protector body (the dry-type transformer body is placed in the oil tank) is equipped with dry-type transformer oil for insulation.
5. The oil storage tank (oil storage tank) is installed on the oil tank to isolate the inside of the oil tank from the outside world.
6. The safety airway (explosion-proof tube) is installed on the top cover of the fuel tank to protect the equipment and prevent the fuel tank from being damaged in the event of failure. When the dry-type transformer fails and a large amount of gas is generated, the pressure in the fuel tank rises, and the gas and oil burst through the explosion-proof membrane, thereby preventing the fuel tank from bursting.
7. The gas relay (:) is installed on the pipeline between the dry-type transformer oil tank and the oil storage tank and is the main protection device. There is a float with a silver switch for water and a bezel that can drive the silver switch for water. When the dry-type transformer fails, the generated gas gathers on the upper part of the gas relay, the oil level drops, the buoy sinks, and the water silver switch opens to send a signal; when the dry-type transformer has a serious failure, the oil flow breaks through the baffle, and when the baffle deflects, Drive a group of mechanisms to switch on another water silver switch, send a signal, and trip. (5) Tap changer: In the power system, in order to control the output voltage of the dry-type transformer within the allowable range, the number of turns of the primary winding of the dry-type transformer must be adjusted within a certain range, so the primary winding is generally equipped with Tap, called tap. By connecting different joints on the switch, the number of turns of the original winding can be changed to achieve the purpose of voltage regulation. Tap-changer is divided into on-load tap-changer and no-load tap-changer.
8. Insulating sleeve: installed on the oil tank cover of the dry-type transformer, used to lead the coil lead out of the oil tank and insulate the lead from the oil tank. Porcelain insulating bushing is used below 1KV, inflatable or oil-filled bushing is used for 10 ~ 10-35KV, and capacitive bushing is used for 110KV.
9. Dry transformer oil: requirements: high dielectric strength and low viscosity, high ignition point and low freezing point, no acid, alkali, dust and moisture and other impurities. Function: Strengthen insulation and heat dissipation.
10. Temperature measuring device: monitor the oil level temperature of dry-type transformer. Small oil-immersed dry-type transformers use silver thermometers for water, and large dry-type transformers use pressure thermometers.
Key words:
Mobile Website
Sales Hotline
+86 13852525108
Contact: Mr. Zhan
Telephone: +86-514-85811000
E-mail: xxdq@jsxxdq.com
Address: No. 6-6 Kangmin Road, Yizheng City, Yangzhou City, Jiangsu Province