News

Jiangsu Xinxin Electric Co., Ltd.

Dry-type transformer price-dry-type transformer structure type and structural characteristics of the introduction.


Release time:

2022-10-10

Dry-Type Transformer Price-Type of Dry-Type Transformer Construction It is mainly composed of silicon steel sheet material core and epoxy resin cast coil structure. An insulating cylinder is placed between the high voltage coil and the low voltage coil to increase electrical insulation, and the coils are supported and constrained by spacers.

Dry-Type Transformer Price-Type of Dry-Type Transformer Construction

It is mainly composed of silicon steel sheet material core and epoxy resin cast coil structure. An insulating cylinder is placed between the high voltage coil and the low voltage coil to increase electrical insulation, and the coils are supported and constrained by spacers.

Dry-type transformer price-construction performance:

Encapsulated winding with solid insulation

(2) Unencapsulated winding

Winding: In the two different windings, the high voltage level is the high voltage control winding, and the low voltage is the low voltage primary winding.

According to the relative position of high and low voltage windings, high voltage windings can be divided into concentric type and overlapping type.

The concentric winding is simple and easy to make, and this structure is adopted.

Overlapping type, mainly can be used for the development of special transformers.

Dry-type transformer price-structural characteristics

Dry-type transformers are often used in places with high fire and explosion-proof requirements due to their strong short-circuit resistance, small maintenance workload, high operating efficiency, small size, and low noise.

1, safety, fire prevention, no pollution, can be directly operated in the load center;

2. Adopting advanced science and technology developed in China, with high mechanical design strength, strong short circuit resistance, small partial discharge, good thermal stability, high reliability and long service life;

3, low loss, low noise, energy saving effect is obvious, maintenance-free;

4, good heat dissipation performance, strong overload problem ability, forced air cooling can increase the system capacity can run;

5, good moisture-proof performance, suitable for operation in harsh environments such as high humidity;

6, dry-type transformer can be equipped with a complete temperature detection and protection system, the use of artificial intelligence control signal temperature control management system, can automatically analyze and display the three-phase winding of their respective working environment temperature, automatic start and stop the fan, and has an important alarm, trip settings and other functions;

7. Small size, light weight, small footprint and low installation cost.

Core

dry-type isolation transformer

The cold-rolled oriented silicon steel sheet and the iron core silicon steel sheet are joined by 45-degree full tilt, so that the magnetic flux passes along the welding seam of the silicon steel sheet.

winding form

(1) winding;

(2) epoxy resin plus quartz sand filling casting;

(3) glass and fiber reinforced epoxy resin for casting (I. e. thin insulating material structure);

(4) Multi-strand glass fiber impregnated epoxy resin windings (generally 3 strands, which can effectively prevent the pouring resin from cracking and improve equipment reliability).

HV winding

Generally, a multi-layer cylindrical or multi-layer segmented structure is used.

Wiring

1. Short the "input" and "output" terminals of the transformer, and test the insulation material resistance between them and the ground personnel with a megger. When measured with a 1000V megohmmeter, the resistance is greater than 2m ohms.

2. The cross section of a power line for input and data output of the transformer shall meet the requirements of its current value. According to the current density of 2-2.5A/min2, it can be configured as appropriate.

3. The input and output three-phase power lines should be connected to phase A, B and C respectively according to the bus color of the transformer terminal board. The neutral line shall be connected to the neutral line of the transformer. The shell is connected to the center point of the transformer. Usually, what we call the ground and neutral currents are drawn from the neutral point of the transformer. (If the transformer has a shell, it should be connected to the ground mark of the shell).

Check the data input and output lines to make sure they are correct.

4, the first no-load power-up, observe the test data input and output voltage can meet the design requirements. At the same time, observe the machine to check whether there are abnormal phenomena such as abnormal sound, ignition, peculiar smell, etc. In case of abnormality, disconnect the input power immediately.

Key words:



Business License