News

Jiangsu Xinxin Electric Co., Ltd.

04

2024-06

How to install the transformer?

1. Conditions required for construction (1) The drawings shall be reviewed and detailed operation instructions shall be prepared and approved according to the manufacturer's data. (2) The quality of construction works related to the installation of box-type transformers is in line with the current national construction and acceptance of construction works. (3) The positions of embedded parts and cable embedded pipes shall meet the design requirements, and the embedded parts shall be firm.

2024-06-04

05

2021-08

How dry-type transformer wiring and outgoing line?

Dry-type transformer wiring mode has the following 5 steps: 1. Short-circuit the "input" and "output" terminals of the transformer to test the insulation resistance of the ground wire with a megohmmeter. When measured by 1000V megohmmeter, the resistance value is greater than 2M ohms. 2. The cross-sectional wiring of transformer input and output power lines shall meet the requirements of current value;

2021-08-05

24

2021-07

Do dry-type transformers need to be blackout

Dry-type transformers are widely used in local lighting, high-rise buildings, airports, wharf CNC machinery and equipment and other places. Simply speaking, dry-type transformers refer to transformers whose iron cores and windings are not immersed in insulating oil. So under what circumstances does a dry-type transformer need to be cut off immediately?

2021-07-24

21

2021-07

Dry-type transformer manufacturers tell you the common fault problems of dry-type transformers

In the process of using dry-type transformers for a long time, it is easy to have some fault problems. In order to reduce some unnecessary troubles caused by these problems, we need to carry out timely maintenance on dry-type transformers, so we should constantly sum up experience. Here we will take a look at some common fault problems and solutions in the process of using dry-type transformers.

2021-07-21

17

2021-07

Transformer manufacturers tell you how to judge the transformer failure

In fact, the sound of the transformer can also be seen whether there is any damage to the transformer. If there are several problems in the sound, it means that the transformer has failed and needs to be repaired. These sound problems when the common transformer is in operation indicate that your transformer is broken. Let's take a look at it in detail:

2021-07-17

15

2021-07

Transformer manufacturers tell you transformer construction and installation preparation work

Transformer is the electrical equipment used in electrical equipment, which can stabilize the voltage and current in the circuit. If the transformer wants to obtain a better power supply effect and ensure its stability, it is especially important to install the transformer. There are different installation methods for the installation and construction methods of transformers. Next, let's pay attention to the installation steps.

2021-07-15

13

2021-07

The difference between dry-type transformer and oil-immersed transformer

Oil-immersed transformer is oil as the main means of transformer insulation, relying on oil as a cooling medium (self-cooling. Air cooling. Water cooling). Generally, the main transformer of the booster station is oil-immersed, with a transformation ratio of 20KV/500KV. Dry-type transformers rely on air convection for cooling. Small capacity transformer ratio 6000V/400V. Dry-type transformers and oil-type transformers, in addition to the same working principle, the big difference is that there is no oil inside the transformer, and there are many differences.

2021-07-13

08

2021-07

Transformer manufacturers tell you what to do when the transformer encounters problems?

When the tap changer is regulated, the noise is increased. The DC resistance value of the double-arm bridge is tested, and it exceeds 2% of the original factory data, which is caused by dirt on the contact. When the transformer is running. Sound strength is proportional to the size of the operating voltage and load current. This is the sound of the normal operation of the transformer. If other sounds appear, the transformer is faulty. The 6/0.4KV distribution transformer is analyzed as follows.

2021-07-08

05

2021-07

Main components of oil-immersed transformer

The big difference between oil-immersed transformer and dry-type transformer is that there is wood and "oil", and because oil is liquid and has liquidity, oil-immersed transformer * must have a shell, and the inside of the shell is aviation hydraulic oil. The electromagnetic coil of the transformer is soaked in the oil, and the electromagnetic coil of the transformer cannot be seen from the outside. However, the dry transformer has no oil and no casing, and the electromagnetic coil of the transformer can be seen immediately; one feature is that the oil-immersed transformer has a conservator on it and aviation hydraulic oil is stored inside. However, the new three-phase oil-immersed transformer is also manufactured without oil conservator;

2021-07-05

16

2021-06

Step-up process of dry-type transformer

Common dry-type transformer is an important power equipment, and the voltage is constantly adjusted. However, due to certain needs, dry-type transformers are also boosted, and the boosting process is more complicated, and the principle is more. We still and dry-type transformer manufacturers to understand the specific principle of dry-type transformer boost:

2021-06-16

< 12 >

Business License